Repairs to uPVC Windows

uPVC windows are a fantastic option for sash modern homes. They are easy to maintain and are durable and long-lasting. In contrast to aluminium and timber, they don't rust or rot.

Regularly cleaning and lubricating UPVC windows and doors is essential. This will help avoid unnecessary repair costs and improve energy efficiency.

1. Broken Glass

The broken glass in your windows could cause severe damage to your home and even be fatal. It is important to take the time to ensure that you are doing everything you can to ensure that your windows are in good condition.

For single pane windows it is fairly easy to replace them, and the new window is usually able to fit into the frame that was previously installed easily. However, if you have double glazing repairs-pane windows that are held in place by internal beading, it will be more difficult to remove the panes that are in place and replace them with new ones. In this situation you'll need source some plastic spacers that will help the new pane to fit correctly into the window frame.

If you're planning attempt to remove the window panes yourself it is important to wear the proper safety gear, including thick gloves and eye protection. It is also recommended to lay down a drop cloth before you begin working on the window panes, so that any shards of glass fall onto the fabric and not on the floor, where they could be trampled.

After the glass has been removed and the glass is removed, it's a good idea to cover the gap with some clear packaging tape or duct tape to block water and drafts from getting into the home until a professional is able to come out and repair the window. This will also provide an obstacle to stop criminals from getting into your home. If the gap is particularly large, you might be interested in the security door with an integrated window as it offers the best of both worlds.

2. Sagging

Upvc windows and doors are a cost-effective, durable and energy-efficient alternative to timber sash windows. However, with time, they can suffer from a variety of issues like sagging. A window that isn't properly aligned can cause problems with light, draughts and even security. If you find that your uPVC window is beginning to shrink, it is important to act swiftly to stop the issue from getting worse.

Repositioning the hinges can help fix a window that is sliding. To accomplish this, you'll need open the window so that you can get to the frame. Then, remove both the hinges on the top and bottom using a screwdriver, and then adjust them clockwise or counter-clockwise. Once you've adjusted the hinges, shut your window and verify the an appropriate fit. If you're satisfied with the fit of your window, tighten the screws to hold them in the right position.

If you are unable to move the hinges, you may need to replace the seal. Rubber seals can dry out and lose their elasticity over time, which causes them to lose their tightness. It is important to replace your seal as soon as you can in order to keep your uPVC window watertight and draughtproof.

uPVC handles can also loosen up. Most often, this is caused by screws that have become loose over time. However, it could be due to the fact that the handle mechanism has worn out. Luckily, it's not difficult to fix the loose uPVC window handle yourself. First, you'll need close your window and do an initial test to ensure that it fits. The joints at the corners of the sash should align with the joint on the casing. If it isn't then you can use a screwdriver to loosen the handle, and then turn the mechanism back into the position it was in.

3. Water Leaks

If you awake to damp floors and mouldy walls each time it rains, sash it's crucial to take action. The leaks of water through windows could cause structural damage to your home and hinder your ability to control the temperature in your home. Most often, uPVC window leaks are caused by a lack or damage to the sealant.

This is a simple fix that can be done by anyone who is a DIYer with the skills. Depending on the severity of the issue is, old caulking may need to be removed. When it comes to uPVC repair, you must avoid over-caulking. This can make your window more difficult to clean and lower its energy efficiency.

It is important to check that any drainage holes are clear of debris and that the sill pan is angled in a way that allows it to drain away from the window. In more serious cases, you may need to replace the window.

Mold spots and rotten sills are also signs of water leakage. The fungus thrives in humid conditions and can propagate quickly throughout the home.

If the leakage occurs between the double-glazed glass, it is more likely that the issue is with the seal rather than the frame. A uPVC specialist can fix this issue by replacing the glass seal. This will ensure the complete insulation of your windows.

4. Faulty Hinges

If your uPVC windows are difficult to open, or are loose and open in a breeze it could be hinges that are at the fault. They can be replaced by any competent DIYer and can usually be completed in just a few minutes.

Nearly every home in the UK will have either top hung or side-hung uPVC windows that use hinges and like any mechanical part they will wear out over time. The process of replacing a hinge on a window is an easy process, but it's easier when you have a person to help you hold the frame up.

Check that the uPVC hinges are open and closed in the proper direction. Check for the arrows on each hinge to determine the direction in which the window should be opened.

The issue could be caused either due to opening the window in the wrong way or by a poor installation at the factory. Sending us a picture through our website can often solve the issue. We are always happy to offer assistance.

It is also essential to grease the hinges regularly. This can be accomplished by applying an oil that is light in nature to the hinges. We suggest using a solvent-free lubricant, such as the 3-in-one Multi-Purpose oil. Regularly lubrication will help the window to operate and close more easily. It also decreases the possibility of a window getting stuck and stop corrosion. This should be done at least every year. WD40 and other solvent based lubricants are not recommended as they could damage parts of your uPVC window.

5. Draughts

Draughts can be caused by several different things. Firstly the hinges, again due to wear and tear may become displaced, which causes an opening to appear where the sash meets the frame. If they are damaged beyond repair, it may be required to realign them. Secondly the interlock, this is located on the hinge side of the window, may also be misaligned, and again it is possible to give them a thorough clean, however in some cases it might be necessary to have these replaced.

The next most common cause of draughts is the window seals. These are prone to wear or damaged over time, and will allow air to escape through these gaps. This can be avoided by replacing them with high-quality weatherstripping. Replace the windows made of Upvc with low-emissivity lenses. This will help regulate indoor temperatures and lessen the possibility of draughts.

One of the most effective methods to reduce draughts is by using a draught excluder. These are typically made of fabric filled with some kind of filler. They can be placed on the top of your windowsill. These will keep your home warm by blocking cold air.

Your windows made of upvc will keep providing excellent insulation and security to your home by performing regular maintenance and repairs. It is important to remember that all windows will eventually become worn out, and it may be more cost-effective to replace them than to repair them. If you have any problems with your Upvc window you should consult an expert as soon as possible.